Joined
·
61 Posts
Yes,,, have a medical card...
What have you done to your bike today?
13801 - 13820 of 13831 Posts
Just got my '22 MT-09 last week and threw on some GB Racing engine covers two days ago. I also threw on some sliders everywhere that you could. Today it started raining in SoCal out of nowhere. I was waddling my bike outside of the garage and lost my footing. Had to let her down. It was not at all a hard fall. Even so, it would have caused some ugly scratches on my new baby. Luckily, the sliders and covers did their job!
Joined
·
3,524 Posts
We don’t have our license/endorsement yet. I think we want to do at least one endurance race with N2 this year. So the plan will be to take the race school, then go get licensed with WERA.
Track day schedule is currently to do VIR Patriot early April, then NCBIKE April 27-30. (27-28 is Champ School, then 29-30 is N2 track days.)
May 20-21 is PTC.
After that I’ll be out there every weekend if I can.
Joined
·
10 Posts
Newbie here, just picked up a new 22 base in black. Added a Puig screen and relocated the horn. It’s too damn cold to ride and I’m itching real bad.
The horn was relocated to an open M6 hole behind the left radiator mount with the stock mount. It’s a tight fit between the bottom tree and the radiator but it has 2-3mm of clearance on both.
![Automotive tire Automotive lighting Automotive design Motor vehicle Carbon]()
![Fuel tank Motorcycle Automotive lighting Hood Light]()
Hoping to get my head lift stand next week and setup the suspension, scrub in tires and enjoy. If it gets close to 50 degrees today I’m going on a chilly scrub in ride.
The horn was relocated to an open M6 hole behind the left radiator mount with the stock mount. It’s a tight fit between the bottom tree and the radiator but it has 2-3mm of clearance on both.
Hoping to get my head lift stand next week and setup the suspension, scrub in tires and enjoy. If it gets close to 50 degrees today I’m going on a chilly scrub in ride.
Prepped to install a rear luggage rack from Shad. The box came and there was a massive rip along one side. All of the installation hardware has slipped out of it lol. Waiting to hear back from RevZilla on what to do next. The thing that sucks is, that was the only one that had in stock when I ordered. So I doubt they'd have another one to send out.
Anyways also installed a fuse block and rewired my GPS and installed the heated grips. Heading out for some camping today to test out the setup. No pics of install yet since it was a bit of a rush job, but I'll post up once it's a bit tidier.
Anyways also installed a fuse block and rewired my GPS and installed the heated grips. Heading out for some camping today to test out the setup. No pics of install yet since it was a bit of a rush job, but I'll post up once it's a bit tidier.
Joined
·
12 Posts
smoked my old tire so i can justify putting new tires
Burnout before new tires 💨💨 #vancouver #yamaha #yamahamt09 #yamahamt09sp #mt09 #mt09sp
Burnout before new tires 💨💨 #vancouver #yamaha #yamahamt09 #yamahamt09sp #mt09 #mt09sp
Joined
·
10 Posts
Finished off the tail tidy and integrated light, from TST. The LED tag light is super bright, almost too bright.
Still have the itch to throw more money at her on trinkets but I’m efforting to save for the suspension.
![Tire Wheel Land vehicle Vehicle Fuel tank]()
![Fuel tank Tire Vehicle Automotive lighting Automotive tire]()
![Tire Wheel Bicycle tire Motor vehicle Automotive tire]()
Still have the itch to throw more money at her on trinkets but I’m efforting to save for the suspension.
Joined
·
35 Posts
Installed -1 front sprocket.
Wow.
Just wow.
It just pulls and keeps pulling.
Best $20 I've spent.
Wow.
Just wow.
It just pulls and keeps pulling.
Best $20 I've spent.
Joined
·
3,524 Posts
I did a +1 to my rear last season. I noticed a better drive on corner exit.
Might have to try a -1 on the front. (I never get to top speed anyway on the straights.)
I have the exact same setup. Does yours fit closer to the bike in the right side as well?
On mine, the right saddlebag is about 1 cm closer to the seat/subframe compared to the left side. It's not a big deal really, just curious.
I send you photos and mine is perfectly assembled, I did it right away.
It doesn't look good in the photos, but it's ok and symmetrical.
The side supports are attached to a central plate and there is a gap of effectively 1cm, so that you can adjust, you have to loosen the screws and insert the supports as close to the bike as possible.
If it has been done by a professional workshop, .... let them do it right...
Joined
·
61 Posts
Used my small Nelson Rigg tail bag to haul six 24oz. beers, extra action cam, 4 packs of cigs, pipe and fixings yesterday. 3 miles of ride on torn up country dirt/gravel road. Beers were a bit excitable for a hour or so. The tail bag did great! 🤙
Joined
·
640 Posts
Any progress to report? Riding in the dark and have been looking at this headlight for some time 🧐
Joined
·
10 Posts
Had a good vibe going from my buddy’s garden and looted my suspension budget for black levers; never shop when your high as a Georgia pine…
Working the weekend, might get to the install Sunday.
![Plant Flower Purple Terrestrial plant Petal]()
![Hood Sunglasses Guitar accessory Bumper Automotive exterior]()
Working the weekend, might get to the install Sunday.
Attachments
13801 - 13820 of 13831 Posts
